Fisher Paykel DD24DI9N Guía de instalación

59186 A 08.17INSTALLATION GUIDEUS CADD24DI, DD24DTI & DD24DHTI modelsDOUBLE DISHDRAWERTM DISHWASHER

98 CAVITY PREPARATIONWater ConnectionRecommended HOT(Maximum 140°F/60°C).Supplied hose tosuit 3⁄8” (9 mm) malecompression fitting.Kosher requirementsD

109 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGELEFT HAND SIDE RIGHT HAND SIDEDrain hoses - 78 1/2” (2000mm)Drain hoses - 70 1/2” (1800mm)In

11(x2)!0 RECOMMENDED METHOD (A) - SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY ONLY)NOW CHOOSE WHICH INSTALLATION METHOD (A) OR (B) IS MORE SUIT

12213(x2)!2-A SECURE TO THE CABINETRY ON THE SIDES!4-A AFTER SECURING, REFER TO ‘FIT THE SUPPLIED TOEKICK PANEL’ STEP!3-A OPTIONALLY SECURE TO T

13(x2)!0 ALTERNATIVE METHOD (B) - SECURE BY DRAWER REMOVALAs you push product in, pull through hoses and cord, ensuring they don’t get kinked or twist

14x4(x2)!2-B SECURE TO THE CABINETRY ON THE SIDES !3-B OPTIONALLY SECURE TO THE CABINETRY ABOVESecure using two pairs of formed brackets. Repeat o

15!5 INSTALLING CUSTOM FRONT DRAWER PANELS112Electrical Shock HazardWARNING!Before continuing, ensure that the product is disconnected from the power

16!5 INSTALLING CUSTOM FRONT DRAWER PANELS2325/8” (16mm)(x6)41125/8” (16mm) (x3)!5-C ATTACH CUSTOM PANELS TO PANEL BRACKETSThere must be at least3 s

17!5 INSTALLING CUSTOM FRONT DRAWER PANELS!5-E CONNECT THE KNOCK-TO-PAUSE MODULE TO THE CONTROLLER!5-G ATTACH CUSTOM PANELS TO PRODUCT!5-F RECONN

18!6 FITTING A CUSTOM TOEKICK PANELPROFILE APROFILE B9Custom Toekick PanelToekick mounting bracket cutting templateCustom toekick panelToekick mountin

11 SAFETY AND WARNINGS WARNING!Electrical Shock HazardWARNING: To reduce the risk of electrical shock, fire, or injury to persons, the installer mus

19!6 FIT THE SUPPLIED PREFINISHED TOEKICK PANEL (IF PREFERRED)1234191956897IMPORTANT!Do not overtighten screw.Slide the toekick onto the mounting rail

2012!7 THERE ARE THREE DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE.DRAINAGE OPTION 1Dishwasher and Ø 1 1/2” (38 mm) Standpi

21min. R 8” (200 mm)IMPORTANT!Ensure that drain connection will comply with local plumbing regulations.IMPORTANT!We recommend the use of a commerciall

22123min. R 8” (200 mm)IMPORTANT!Ensure that drain connection will comply with local plumbing regulations.DRAINAGE OPTION 3Dishwasher using drain hose

23Ensure the supplied rubber washer is fitted inside the coupling.Tighten coupling with spanner.180oNo leaks!12@0 TROUBLESHOOTING ●Excessive water rem

24@1 FINAL CHECKLISTTO BE COMPLETED BY THE INSTALLERComplete and keep for safe reference:Model Serial No. Purchase Date Purchaser Dealer Address I

26

22 PARTS SUPPLIEDIf the Drain hoses supplied are not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which wi

33 OPTIONALLY HARD WIRING PRIOR TO INSTALLATION3-A REMOVE THE LOWER DRAWER 3-B REMOVE THE ACCESS COVER & REMOVE POWER Access coverClipClipEl

43 OPTIONALLY HARD WIRING PRIOR TO INSTALLATIONIMPORTANT!Ensure the mains wires are routed UNDERNEATH all other harness wiring from the electronics

54 PRODUCT DIMENSIONSSTANDARDHEIGHTMODELSTALLHEIGHTMODELSPLANPROFILEFRONTDD24DIDD24DTIDD24DHTIPRODUCT DIMENSIONS INCHES (MM) INCHES (MM)AOverall

65 CABINETRY DIMENSIONSMinimum clearances from adjacent cabinetrySTANDARDHEIGHTMODELSTALLHEIGHTMODELSDD24DIDD24DTIDD24DHTICABINETRY DIMENSIONS INC

76 CUSTOM DRAWER PANEL SPECIFICATIONSThe following calculations assume the top of the upper panel is aligned with the top of the adjacent cabinetry.

87 CUSTOM TOEKICK PANEL SPECIFICATIONSHEIGHT OF THE TOEKICK PANELMeasure D (height from the top of adjacent cabinet door fronts to the floor) and wr